Forums
New posts
Search forums
What's new
New posts
New media
New media comments
Latest activity
Gallery Index & Tech Ref
Goldwing Trivia
Goldwing- The First 20 Years
From Japan to USA
Goldwing Magazine Articles
Two Wheel Magazine 1975- Honda's GL1000, The Future
Cycle Illustrated, Nov. 1975- 2 Big Ones From Honda
1977 Model GL1000 Setup Instructions
Owners Manuals
GL1000
1975 GL1000
1978 GL1000
GL1100
1980 GL1100 Standard
1981 GL1100 Interstate
1982 GL1100 Aspencade
1982 GL1100 Interstate
1982 GL1100 Standard
1983 GL1100 Aspencade
1983 GL1100 Interstate
GL1200
1984 GL1200 Standard
1986 GL1200 Interstate
1987 GL1200 Aspencade
GL1500
1987 GL1200 Aspencade
Service Bulletins and Recalls- All Models
GL1000
GL1000- Important GL1000 Service Reminder (1 Page) 6-13-1975
SL #108 Tire and Wheel Rim Matching Information 6-20-75 (7 pages)
Service Tools Newsletter 7-31-75 (2 pages)
SB 1000 #3 Pressurised Cooling System Tester 10-10-75 (3 pages)
SB 1000 #1 Cylinder Head Core Plug Leakage- Revised 7-9-76 (3 pages)
SL #117 Exhaust Pipe and Muffler Paint Damage 9-30-76 (1 page)
SL #118 Instrument Troubleshooting 10-27-76 (5 pages)
PB 1000-2 Changes to Clutch Components 11-3-76 (1 page)
PB 1000-3 Changes to Right Front Engine Cover 1-5-77 (1 page)
SB 1000 #11 Final Drive Gear Case Cover Change 10-15-77 (1 page)
SB 1000 #12 New Main Bearing Caps 11-23-77 (1 page)
SB 1000 #13 Recall to Replace Rear Brake Pads 3-21-78 (5 pages)
SB 1000 #14 Cylinder Head Bolt Torque Change 11-8-78 (1 page)
GL1200
Special Consumer Report: 1984 and 1985 GW Rear Hub
New media
New comments
Search media
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
General Discussion
New Member Forum (Start Here)
Hello from Sydney Australia
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Help Support Classic Goldwings:
This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Message
<blockquote data-quote="Mojo_Tele" data-source="post: 194311" data-attributes="member: 5194"><p>Thanks a lot for the welcome gents, I really appreciate it. </p><p></p><p>Here's her original ad, <a href="https://m.facebook.com/story.php?story_fbid=1874116159530134&id=1493937544214666&_rdr" target="_blank">https://m.facebook.com/story.php?story_fbid=1874116159530134&id=1493937544214666&_rdr</a></p><p>_________________________________</p><p></p><p>Progress to date,</p><p>- 30 year old tank clean (Evapo-Rust, tank in bike). Done, used 120 ping-pong balls to displace the Evapo-Rust which costs like $85 a 1.5 gallons. I needed 3 containers. Was more varnish & crud than rust... but still impressed with the Evapo-Rust impact.</p><p>- belts done (they were originals with cracking all around - so thank God they are out),</p><p>- Rear master cylinder, was actually rear brake pivot pin needing a good moly grease & clean. Done.</p><p>- air cut-off valves were "gummy". Done. No holes but they were perishing. Did this patiently with the carbs still assembled using 90deg #2 Phillips. I can only hope that the stuttering on accelerations was from shyte fuel & contamination. New fuel filters coming. New fuel line & clamps ready to go. Stabil added to full fresh tank of fuel.</p><p></p><p>Still To do,</p><p>- Tyres, dated them as '92 & '95 - could that be right for Elite II's?</p><p>- Speedo cable (I have it already)</p><p></p><p>_________________________________</p></blockquote><p></p>
[QUOTE="Mojo_Tele, post: 194311, member: 5194"] Thanks a lot for the welcome gents, I really appreciate it. Here's her original ad, [url]https://m.facebook.com/story.php?story_fbid=1874116159530134&id=1493937544214666&_rdr[/url] _________________________________ Progress to date, - 30 year old tank clean (Evapo-Rust, tank in bike). Done, used 120 ping-pong balls to displace the Evapo-Rust which costs like $85 a 1.5 gallons. I needed 3 containers. Was more varnish & crud than rust... but still impressed with the Evapo-Rust impact. - belts done (they were originals with cracking all around - so thank God they are out), - Rear master cylinder, was actually rear brake pivot pin needing a good moly grease & clean. Done. - air cut-off valves were "gummy". Done. No holes but they were perishing. Did this patiently with the carbs still assembled using 90deg #2 Phillips. I can only hope that the stuttering on accelerations was from shyte fuel & contamination. New fuel filters coming. New fuel line & clamps ready to go. Stabil added to full fresh tank of fuel. Still To do, - Tyres, dated them as '92 & '95 - could that be right for Elite II's? - Speedo cable (I have it already) _________________________________ [/QUOTE]
Insert quotes…
Verification
Post reply
General Discussion
New Member Forum (Start Here)
Hello from Sydney Australia
Top