Recent content by Curlytops

Help Support ClassicGoldWings:

  1. Curlytops

    SEI 1200 Running Issues ….. still☹️

    Heres them both together..
  2. Curlytops

    SEI 1200 Running Issues ….. still☹️

    God yes it feels a lot lighter and certainly not as top heavy… you sit in the 1800s and not on them .. riding position of the 1800 is far superior as you would expect it to be. 👍
  3. Curlytops

    SEI 1200 Running Issues ….. still☹️

    Well I did all my final testing and the SEI rides great... Thankyou for your help with sorting it out, Im thinking now because of the complex nature of this beast Im going to move it it on and look for a GL1000 or 1100 to work on during the winter months.... Id forgotten just how heavy these are...
  4. Curlytops

    SEI 1200 Running Issues ….. still☹️

    Okay… i backed everything off so i could get the feeler gauges in as the throttle stop was holding the linkage. Checked TPS voltage and was .47v. Started bike and it was still running rough at low revs under load but ticking over fine…. I went back to original diagnosis which was PB sensor. I...
  5. Curlytops

    SEI 1200 Running Issues ….. still☹️

    HI... Thanks for the info, Im going to do that today and will post here how I get on ..thanks for the help I really appreciate it and am slowly getting my head around this CFI stuff.
  6. Curlytops

    SEI 1200 Running Issues ….. still☹️

    Hi.. I was slightly confused when reading the supplement and looking at your pic. It says to check the TPS to loosen the idle speed screw and then put a 2.9mm gauge between that and the arm. So should the throttle stop be as mine is and i insert the gauge to lift it away from the arm, or should...
  7. Curlytops

    SEI 1200 Running Issues ….. still☹️

    No its not a dumb question at all.. I have had the injectors out and they are functioning correctly and do have a good spray pattern. Im only going through fuel system at the moment as the previous owner said this was where the fault was, but once ive got my head around the fuel system then I...
  8. Curlytops

    SEI 1200 Running Issues ….. still☹️

    Thanks i have located the plug now and spliced in some wires, i rechecked the TPS and i got the same readings., 0.47v with throttle closed going smoothly up to 4.1V throttle wide open. I then rechecked with an old needle multi meter, and got the same readings, and the needle moves slow and...
  9. Curlytops

    SEI 1200 Running Issues ….. still☹️

    OK .. I have tested my TPS voltage, and with the throttle at rest its 0.47V. As I open the throttle it rises to a max of 3.45V. Is this within spec does anyone know? If not and i have to swap out the TPS how do I get it off, as it looks to have no bolt or screw heads on it...?
  10. Curlytops

    SEI 1200 Running Issues ….. still☹️

    Hi Rednax.. Had a bit more time with the wing today, wing started as normal, and settled back to its 950rpm as usual , still sounded a bit rough when low revved. I wired up the suzuki PB sensors I had and gave them a go, the tickover was then 3000rpm and i couldnt get it lower so not sure what...
  11. Curlytops

    SEI 1200 Running Issues ….. still☹️

    BTDT? It looks to have had a TPS added at sometime with bad soldering… i remade the joints but I haven’t checked its calibration ill look into it 👍
  12. Curlytops

    SEI 1200 Running Issues ….. still☹️

    Hi… im still having issues trying to get this sei to run right… it starts on the button, when cold revs at around 1800rpm and once warm settles at around 950rpm. once warm it revs ok but seems to bog down up to below 3000rpm. I rode it up the street and it sound like its missing at low revs and...
  13. Curlytops

    Hi Idle issues.

    Hi .. not posted for a while as not had a lot of time to work on the wing. i have a question about PB sensor connections... i managed to get a set from the states but they have the wrong connections on the end as i wasn’t aware at the time there were 2 types. the set that arrived have the round...
  14. Curlytops

    Fork oil seals.

    Im on about the hex bolt that goes up the fork leg at the bottom... is that the drain bolt? Yep i remember the fork caps I had an old towel over them to catch them... ill let you know how i get on... just awaiting my parts arrival.
  15. Curlytops

    Fork oil seals.

    Hi.. Ive looked through the various posts about this on the forum, and have done 1200 forks before but it was a long time ago. Bike is a 1986 SEI, and while im in there I will be replacing the bushings as well. I know I loosened the fork caps while the forks were in the bike, but I cant remember...
Top