Forums
New posts
Search forums
What's new
New posts
New media
New media comments
Latest activity
Gallery Index & Tech Ref
Goldwing Trivia
Goldwing- The First 20 Years
From Japan to USA
Goldwing Magazine Articles
Two Wheel Magazine 1975- Honda's GL1000, The Future
Cycle Illustrated, Nov. 1975- 2 Big Ones From Honda
1977 Model GL1000 Setup Instructions
Owners Manuals
GL1000
1975 GL1000
1978 GL1000
GL1100
1980 GL1100 Standard
1981 GL1100 Interstate
1982 GL1100 Aspencade
1982 GL1100 Interstate
1982 GL1100 Standard
1983 GL1100 Aspencade
1983 GL1100 Interstate
GL1200
1984 GL1200 Standard
1986 GL1200 Interstate
1987 GL1200 Aspencade
GL1500
1987 GL1200 Aspencade
Service Bulletins and Recalls- All Models
GL1000
GL1000- Important GL1000 Service Reminder (1 Page) 6-13-1975
SL #108 Tire and Wheel Rim Matching Information 6-20-75 (7 pages)
Service Tools Newsletter 7-31-75 (2 pages)
SB 1000 #3 Pressurised Cooling System Tester 10-10-75 (3 pages)
SB 1000 #1 Cylinder Head Core Plug Leakage- Revised 7-9-76 (3 pages)
SL #117 Exhaust Pipe and Muffler Paint Damage 9-30-76 (1 page)
SL #118 Instrument Troubleshooting 10-27-76 (5 pages)
PB 1000-2 Changes to Clutch Components 11-3-76 (1 page)
PB 1000-3 Changes to Right Front Engine Cover 1-5-77 (1 page)
SB 1000 #11 Final Drive Gear Case Cover Change 10-15-77 (1 page)
SB 1000 #12 New Main Bearing Caps 11-23-77 (1 page)
SB 1000 #13 Recall to Replace Rear Brake Pads 3-21-78 (5 pages)
SB 1000 #14 Cylinder Head Bolt Torque Change 11-8-78 (1 page)
GL1200
Special Consumer Report: 1984 and 1985 GW Rear Hub
New media
New comments
Search media
Members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Classic Goldwing Technical Forums
General Classic Goldwing Technical Forum
Newbie error when changing brake pads on 86 aspencade
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Help Support Classic Goldwings:
This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Message
<blockquote data-quote="glkm" data-source="post: 125154" data-attributes="member: 3412"><p>Well, I thought I read the book thoroughly before I started, but I missed one small very significant detail. I pulled the caliper off my front left (front brakes needed a lot of pressure to stop at slow speed). I had a previous fork seal leak (which I fixed with new seals and progressive coils) which coated my front left rotor and pads. Pulled the pads and they were almost down to metal - pistons out about an inch or so. I bought new pads, used a c-clamp to push the pistons back in and heard a very high pitched noise from the top of the bike, then all of a sudden a release and my plastic window in my master cylinder was bouncing off my RV side. :doh: </p><p>I had neglected to take the top off the MC or open the bleeder valve at the caliper. Found out that that window is not replaceable, so just pushed it back in, finished the pad swap, refilled the MC, cleaned all the brake fluid off the MC and tried the lever. Very quickly it became firm so I kept squeezing the handle as hard a I could to see if and when the plastic window would pop out again. Nothing, no leaks. I am flummoxed. :headscratch: </p><p>Does anyone know why? Any idea if I am totally :sensored:? Has this happened to anyone else and does anyone have any advise?</p><p></p><p>Thanks in advance - Gavin</p></blockquote><p></p>
[QUOTE="glkm, post: 125154, member: 3412"] Well, I thought I read the book thoroughly before I started, but I missed one small very significant detail. I pulled the caliper off my front left (front brakes needed a lot of pressure to stop at slow speed). I had a previous fork seal leak (which I fixed with new seals and progressive coils) which coated my front left rotor and pads. Pulled the pads and they were almost down to metal - pistons out about an inch or so. I bought new pads, used a c-clamp to push the pistons back in and heard a very high pitched noise from the top of the bike, then all of a sudden a release and my plastic window in my master cylinder was bouncing off my RV side. :doh: I had neglected to take the top off the MC or open the bleeder valve at the caliper. Found out that that window is not replaceable, so just pushed it back in, finished the pad swap, refilled the MC, cleaned all the brake fluid off the MC and tried the lever. Very quickly it became firm so I kept squeezing the handle as hard a I could to see if and when the plastic window would pop out again. Nothing, no leaks. I am flummoxed. :headscratch: Does anyone know why? Any idea if I am totally :sensored:? Has this happened to anyone else and does anyone have any advise? Thanks in advance - Gavin [/QUOTE]
Insert quotes…
Verification
Post reply
Classic Goldwing Technical Forums
General Classic Goldwing Technical Forum
Newbie error when changing brake pads on 86 aspencade
Top