Help needed 1986 interstate GL 1200 starts Warms up turn off go back to start only backfires very loud

Classic Goldwings

Help Support Classic Goldwings:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Joined
Aug 25, 2022
Messages
10
Reaction score
5
Location
Hercules
My Bike Models
1986 GL 1200 interstate
I have a 1986 Honda Goldwing inters
4074E1F8-6666-4769-8632-E40DD0B2D189.jpeg
tate I’ve rebuilt the carburetors sank carbs adjusted air fuel changed ignition coil wires and plugs. It starts beautifully runs great, until it warms up and you turn it off after letting it sit for a minute if you try to start it just has a loud backfire. I am very good at remove and replace. Troubleshooting I’m weak need help
 
I would let it sit after a run for maybe 10 min. and pull the plugs, if you have a camera all the better, have a look inside the chamber and see if there is wetness, smell the plug for fuel smell, I am not sure if 1200 has a wasted spark ignition but my gut is telling me you have a cylinder flooding after shut down, heat can cause ethanol laced fuel to purge under heat, it has about a 170 degree boiling point and if a cylinder is flooding during a wasted spark an exhaust valve is open causing a backfire.
 
I knew a guy that put a Mazda rotary into a Triumph Spitfire. Overfueling caused a backfire that blew apart the muffler and lifted the car off the ground. It was loud enough for the police and fire department to be dispatched for a terrorism attack lol
 
It's probably the pulse generators.
That’s what I think it is I have a parts bike I have four GL 1200s to aspens and two interstates one is a parts bike on the yellow and white leads going to the four-way plug. It shows that it’s a closed circuit on the blue and blue and white lead to the four-way plug. It reads open. I have been looking in all the wrong places for information on this and have not found what I’m looking for. Maybe you can help me.
 
Look at this wiring diagram....
https://classicgoldwings.com/media/page-142.19766/

It shows the color of wires and based on what you state the 'blue' doesn't sound right. You need to measure ohms on the pairs to see if they are good or bad. I don't remember the resistance (ohms) it should read (memory is thinking in the 300 range). If you have other pulse generators you can measure them to compare to what you have. You need to have the unit unplugged for measurements.

Best of luck...
 
Look at this wiring diagram....
https://classicgoldwings.com/media/page-142.19766/

It shows the color of wires and based on what you state the 'blue' doesn't sound right. You need to measure ohms on the pairs to see if they are good or bad. I don't remember the resistance (ohms) it should read (memory is thinking in the 300 range). If you have other pulse generators you can measure them to compare to what you have. You need to have the unit unplugged for measurements.

Best of luck...
Thank you very much for this information. I am on vacation right now. Sorry I didn’t get back to you earlier. When I get home next week, I will get right on it. I have a parts bike. I might pull one side of it out of my parts, bike, and Mary it together With my problem bike they should both be the exact same so I do not think I will have a problem. What do you think?
 
If it was me, I would replace both while I was in there. My luck would be the other one fails right after it's all put back together.

I may not have been clear on the ohm test, the measurement would be done without the part being in the bike (ie the sensor not sensing anything metal).
 
Last edited:
If it was me, I would replace both while I was in there. My luck would be the other one fails right after it's all put back together.

I may not have been clear on the ohm test, the measurement would be done without the part being in the bike (ie the sensor not sensing anything metal).
Hey there thank you very much I got back and yes, one is bad. The other is showing about 330 ohm. I understand I do not like using use electrical parts myself. Do you know anywhere I could find the replacement part Honda says it’s discontinued. I’d search a couple of other websites eBay and Amazon and haven’t found a set. I would really like to get this bike back up and running. Thank you very much for your time.
 
The key to longevity of electrical components in an oil bath is an efficient cooling system. Heat crystalizes and breaks down winding insulation.

I got into a huge argument on another forum for this bike model line with a self-imagined expert with 10,000 post who seemingly sits and monitors every thread in order to puff his ego as an authoritative contrarian. In response to a new member was concerned about the bike running hotter than comfortable he insisted "that's good, I run mine hot" without taking into consideration the possibly of the guy having an unfortunate electrical failure in the middle of nowhere.

That's why I went from there to here.

Sorry about my rant.
 
Hey, I would like to thank you guys for your advice. It was something that was staring at me and sometimes you just don’t want to think that that’s the problem I could not find a new pulse generator so I used an old one as you can see. it works fine. Thank you very much, I’ll be going for my first ride today
 

Latest posts

Top